AN1020-25 USER MANUAL PDF

ptcl router manual. An User Manual Router All materials on our website are shared by users. If you have any questions about. USER MANUAL. TestClick ADSL BER Test to perform a bit error rate (25 26Note: If the BER reaches e-5, you cannot access the Internet. Find the default login, username, password, and ip address for your Fiber Home AN router. You will need to know then when you get a new router.

Author: Negore JoJokora
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Art
Published (Last): 14 May 2015
Pages: 404
PDF File Size: 13.17 Mb
ePub File Size: 10.93 Mb
ISBN: 752-1-56986-744-8
Downloads: 47233
Price: Free* [*Free Regsitration Required]
Uploader: Taujas

Modify an existing Internet connection.

User Manual Guide – AN1020-20

Select use the following IP address, and then you can enter the IP address of the gateway. How i can make wifi hotspot with my laptop for my android device, but i dont have router, my internet is from usb modem that dont have wifi feature.

I want the password for this modem. I have brougth a ptcl wifi router 2ndhand. Chemistry Engineering Mathematics Physics. The Subnet Mask is: Leading Today Pts Helpful 1.

The user, through the user configuration tab on page System, can change the passwords.

And upon trying to access device configuration setting, it ask for OS image to get update the firmware. How to connect to ptcl wifi router with a mobile phone without the password? In this page, you can modify Internet connection protocol and encapsulation type. Under wireless set up you will find options to configure WEP encryption.

Check out with softwares available online. Visitors to this page also searched for:. Click OK button to close the Network property dialog box. The frequency of ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. Press Enter key then the entry dialog box will pop up as Figure 2.

Select Use the following IP address. Anonymous “There should be a reset button on your modem or on and It usre like this:. Open the Modem, and connect the USB port. There are 2 additional ways that you can determine your router’s IP address:. The maximum value which default lease time can be set to. The user can set different IP addresses and subnet mask whenever necessary.

The user can usef these addresses through a1020-25 Local Network page. Please help us improve our content by removing questions that are essentially the same and merging them into this ussr.

You will have to check your connection setting and ensure its in 3G or a higher version, the setting depends on your service provider. My internet doesnt works. If you did not see your router’s ip address in the list above. The result is shown in Figure C.

In the Connections page, the default configuration of the modem supports seven PVCs. What is the ptcl U modem security key? By default, it is seconds 12 hour.

Leader Board What’s this?

Check Defaul gateway to access User interface of the router by doing the steps: Type in ipconfig and take note of the default gateway 4.

Plug in the power cord, and turn on the power. How to change password for wifi an router? And i need hotspot for my gaming devices too will it work? I want wifi in my mobile phone samsung an1020-255.

Drivers and Software

Therefore, Internet applications such as synchronous transmission of multi video stream, sn1020-25 games and huge capacity of downloading files are made possible. After a restore my iphone 3g says searching where it used to say no sim and i have no wifi no bluetooth no modem firmware. If you do not want to enable NAT and want the user of the modem to access the Internet normally, you must add a route on the uplink equipment.

Go to Advance Wireless Maual 8.

However im not sure the manufacturer of your ADSL modem. Web-based configuration and monitoring. It is adapted for strict requirement to delay and quality of data packets transmission.

How to Login to the FiberHome AN

Real-time variable bit rate Real-time VBR is adapted for real time with manusl requirement. The default is After the preset time, the lease IP is released. Please tell us which questions below are the same as this one: After the device is powered on, the PPP dial-up performs automatically. Visitors to this page also searched for: Make sure that the correct cable is used.

You should see a dialog box pop up asking your for your FiberHome AN username and password. Yes, but how should i do that.

Author: admin