ASTM D6484 PDF

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Vinos Kataur
Country: Guyana
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 20 February 2018
Pages: 180
PDF File Size: 14.57 Mb
ePub File Size: 1.35 Mb
ISBN: 217-9-11479-117-5
Downloads: 62014
Price: Free* [*Free Regsitration Required]
Uploader: Vora

Tolerances may be applied to a nominal value to de? Threeplace failure mode descriptors, summarized in Table 1, shall be used. Ultimate strength is calculated based on the gross crosssectional area, disregarding the presence of the hole.

Sources of Additional Information: Record the dimensions to three signi? Terminology E asrm Practice E de? An early version of the Boeing Open-Hole Compression Test Fixture included cutouts to clear strain gages bonded to the surfaces of the specimen, and to provide egress for the gage wiring.

If sstm platens are not sufficiently hardened, or simply to protect the platen surfaces, a hardened plate with parallel surfaces can be inserted between each end of the? Combining values from the two systems may result in nonconformance with the standard.

Extensometers shall satisfy, at a minimum, Practice E 83, Class B-1 requirements for the strain range of interest, and shall be calibrated over that range in accordance with Practice E Flag symbol 1 For existing?

ASTM D Compression Fixture for Fiber Composite Laminates| GD

Some types of damage, such as longitudinal splitting and delamination, can blunt the stress concentration caused by the hole, increasing the force-carrying capacity asrm the coupon and the calculated strength.

Estimate the coupon strength to aid in transducer selection, calibration of equipment, and determination of equipment settings. Record and report the specimen cutting and hole preparation methods.

The long and short? The threading of the support c6484 is optional. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

NOTE 5—Other valuable data that can be useful in understanding testing anomalies and gripping or specimen slipping problems includes force versus strain data, percent edgewise bending, and force versus time data.

The torque level may be increased above this level when acceptable failure modes cannot be achieved using 7 N-m [60 in-lbf] applied torque. Chamber conditions shall be monitored either on an automated continuous basis or on a manual basis at regular intervals.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Terminology E 6 de?

NOTE 6—The hole diameter is ignored in the strength calculation; the gross cross-sectional area is used.

ASTM D Open-Hole Compressive Strength of Polymer Matrix Composite Laminates_图文_百度文库

The failure is often astmm in? The following general notes apply to these? Properties that may be derived from this test method include open-hole notched compressive strength OHC. If the gap is too large, shim between the support plate astj the long grip, holding the shim stock on the support plate with tape. Each laboratory tested at ambient laboratory conditions a randomly distributed sample of six specimens for each loading type. The specimen, typically, but not necessarily, a quasi-isotropic laminate, is 12″ long, 1.

Hydraulic grip-loaded data typically exhibit linear behavior at the onset of loading.

Hydraulic wedge grips shall apply sufficient lateral pressure to prevent slippage between the grip face and the support? This fixture is shown in Fig 6. The assembled fixture, with specimen installed, can be gripped at each end by hydraulic grips in the testing machine shear loadingor aligned vertically between flat platens end loading.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM D6484 Testing Fixture

Reduce the compressive force to 7 N [30 lbf], and re-zero and balance all instrumentation. Measure the hole diameter, D, distance from hole aatm to closest coupon side, f, and distance from the hole edge to coupon end, g.

Two types xstm precision xstm repeatability and between-laboratory reproducibility are reported. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Link to Active This link will always route to the current Active version of the standard.

However, since the notch dominates the strength, consistent preparation of the hole, without damage to the laminate, is important to meaningful results.

Author: admin