plain ends. I Seam-Welded Pipe. Seam-Welded Pipe m. EEMUA – Section 2. Manufacturer of Nickel Alloys, Austenitic Stainless Steel and Copper Nickel. CuNi 90/10, UNS CX, EEMUA 90/10, 90/10, 14 90/1, Cu rem. Pb. 01 max. Fe Zn max. P max. S max. Ni Mn , EEMUA Copper Nickel Pipes. Standard:EEMUA Size:DNDN Thickness and Pressure Ratingbar, 20bar. Material:Copper Nickel UNS X.
|Published (Last):||10 March 2017|
|PDF File Size:||5.49 Mb|
|ePub File Size:||2.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Read more on mechanical properties of pipes.
Seawater cooling systems Eemua 144 water systems Sanitary systems Deck steam pipes Hydraulic and pneumatic systems Seawater feed lines to desalination and processing units Splash zone cladding. From this information, the extent eemua 144 which various standards overlap may be compared.
Copper-Nickel Alloy Standards
Since decades, these alloys have successfully used in: Welding The welding consumables used for the manufacturing eemua 144 welded components are in accordance with AWS-A5. Based on ASME specifications, additional components are included. Gaskets should not be used when mating with elastomerlrubber faced flanges.
Eemua 144 contact us for more information.
Fitting for butt welding into copper-nickel-alloy pipelines-Elbows References Standards and Specifications. General principles for the radiographic examination DIN Fitting for butt welding into copper-nickel-alloy eemua 144. The copper-nickel stub end and flange joint faces are machine finished and comply with eemua 144 corresponding Sections of EEMUA Read more.
Merchant and military shipbuilding Offshore oil and gas installations Coastal petroleum and petrochemical processing plants Seawater desalination plants Coastal electricity generation plants Copper-nickel alloys are widely applied in: Despite the rough conditions in marine service and the highly corrosive nature femua seawater, the products provide well balanced combination of technical and economical advantages:. OSNA10 Offshore 2. Variations in the common national and international specifications for theand Eemua 144 alloys are illustrated in Table 2.
The gasket hardness shall eemua 144 be less than 75 Shore. Fitting for butt welding into copper-nickel-alloy pipelines-Tees DIN The specification comprises a series for eemua 144 fittings including butt weld, socket welding, capillary brazing, threaded, selfreinforced fittings as well as saddle pieces.
Offshore : KME – Engineering Copper Solutions
Working pressures and temperatures of components included in this specification. Controlled content of alloying elements and eemua 144 concentration of impurities ensure reliable service and fabrication properties of the alloy. Fittings The specification comprises a series for pipe fittings including butt weld, socket welding, capillary brazing, threaded, selfreinforced fittings as well as saddle pieces.
Technical specifications for tubes DIN Typical international and national standards for ordering wrought and cast forms are presented in Eemua 144 Fitting for butt welding into copper-nickel-alloy pipelines-Saddle type connections DIN Fitting for butt welding into copper-nickel-alloy pipelines-Concentric reducers DIN The gaskets shall eemua 144 be graphited.
Simple alloying system with good weldability Excellent ductility eemua 144 toughness Outstanding erosion corrosion performance Resistant to uniform and localised corrosion No effect of ambient seawater temperatures No effect of seawater chlorination Resistant to biofouling Resistant to stress-corrosion cracking Low maintenance costs A lot of design experience. Since decades, these alloys have successfully used in:. Design Scope Working pressures and temperatures of components included in this specification 1.
Pipelines of copper-nickel-alloys-Part 2: In order to ensure adequate seating when solid eemua 144 and solid slip-on flanges are used, irrespective of gasket materials, the gaskets shall be located within the bolt circle. Although the pipe dimensions of 38 and 40 inch are not included in the EEMUA — they are available here as they are commonly specified in offshore projects.
Loose Flanges and eemua 144 necks for pipes of copper-nickel-alloys DIN The welding consumables used for the manufacturing of welded components are in accordance with AWS-A5. In some standards, the impurities are more closely controlled than in others.
EEMUA 144 Copper Nickel Cu Ni 90 10 C70600 Pipe Bangkok, Thailand
Where there is doubt, advice from the supplier should be obtained. Ships and eemua 144 technology-Design, production and test of pipeline systems for liquid media-Part 1: Gaskets The gaskets normally used with flanges are those made from aramid fibre with nitrile binder in accordance with ASME B Eemua 144 made of copper-nickel-alloys-Part 4: The fit-for-purpose corrosion allowance of 0.
Pipelines of copper-nickel-alloys-Part 9: