1 Jan Steel wire ropes – Safety – Part 1: General requirements; German version EN +A 12 Nov Europastandarden EN gäller som svensk standard. The European Standard EN has the status of a Swedish. You will find the licence in the end of this document.! Europastandarden EN +A gäller som svensk standard. Detta dokument innehåller .
|Published (Last):||14 September 2016|
|PDF File Size:||13.41 Mb|
|ePub File Size:||3.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
Spiral ropes for general structural applications This is the first edition of this Part.
AFNOR Editions Online Store
In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Stainless steels – Part 3: NOTE The requirements for breaking force testing take into en 12385-1 i the rope size, ii whether or not ropes are produced in series i.
Round and en 12385-1 non alloyed steel wire for Terms and Conditions Terms of subscription Online watch.
Quality En 12385-1 coating as given in EN shall be used for zinc coated wires unless specified otherwise in the appropriate part of this en 12385-1. Information regarding online access to British Standards via British Standards Online can be found at http: Steel wire for ropes.
en 12385-1 It cannot, therefore, exist alone. Annex B gives the testing requirements for wires taken from the rope when specified in other Parts of en 12385-1 standard.
Since failure can be 123855-1 by the incorrect choice of specification of steel wire ropes, the other Parts of this: For ropes with shaped e.
CEN – EN – Steel wire ropes – Safety – Part 1: General requirements | Engineering
Steel wire and wire products. Test yourself or your business online. En 12385-1 details of these and other benefits contact Membership Administration.
Additional production lengths en 12385-1 rope from any size grouping shall be deemed to comply with the breaking force requirements when the manufacturer has satisfactorily completed a the appropriate type tests, refer annex A and b a periodic test see Table 1 in en 12385-1 with Method 1 en 12385-1 alternatively, Method 3, as described in 6.
Metal and resin socketing. If one of the samples fails the test, tests shall be carried out on a sample from each of the remaining production lengths. Information for use and maintenance Part 4: In the case of failure to meet the intended minimum breaking force value when tested in accordance with method en 12385-1type testing in accordance with annex A shall be repeated.
Definitions, designation and classification. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. For each of the sub groups representing the intended size range and having the same construction, grade and minimum breaking force factor, the manufacturer shall perform a breaking force test in accordance with 6. ENSteel wire and wire products – Steel wire for ropes – Part 3: Fibre cores FC for single layer stranded ropes larger than 8 mm diameter shall be doubly closed Natural fibre cores NFC shall be treated with an impregnating compound to en 12385-1 rotting and decay en 12385-1 stated that the core is dry.
If all three samples pass the test, that rope diameter and construction having that particular minimum breaking force factor shall be deemed to have satisfied the breaking force type testing requirements. Users are responsible for its en 12385-1 application. Stranded ropes for mine shafts Part 7: Standards are also available from the BSI website at http: NOTE 2 When joints in wires before closing are not accepted, this should be the subject of agreement see introduction between the purchaser and the manufacturer.
This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of en 12385-1 Standards Policy and Strategy Committee on 30 October Summary of pages This document comprises a front en 12385-1, an inside front cover, the EN title page, pages 2 to 18, an inside back cover and a back cover.
It is the constant aim of BSI to improve the quality of our products and en 12385-1. NOTE Breaking force type testing demonstrates that a steel wire rope produced in series and certified by the manufacturer as conforming to en 12385-1 of the other parts, possesses the minimum breaking force stated by the manufacturer. This en 12385-1 not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.
UBAP1 Antibody AP | Proteintech
If all samples pass the test, that rope diameter and en 12385-1 having that particular 1385-1 breaking force or minimum aggregate breaking force shall be deemed to have satisfied the breaking force type testing requirements. If the number of wires that fail these tests is less than two, the wires shall be deemed en 12385-1 comply.
Cold drawn non alloy steel wire for ropes for It shall not be necessary to repeat the tests if the same breaking force factor is used for ropes using wires of a en 12385-1 grade.
If these details en 12385-1 to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.
Locked coil ropes for mine shafts Part 8: NOTE Toqether with the information as qiven in 7. EN 1Steel wire and wire products – Non ferrous metallic en 12385-1 on steel wire – En 12385-1 2: If any rope subject to the periodic test fails to meet or en 12385-1 the minimum value, testing en 12385-1 a sample from each production length shall continue until the manufacturer satisfies the type testing requirements.
For undated references the latest edition of the publication referred to applies including amendments. At each position two measurements, at right angles, of the circumscribed circle diameter shall be taken. Various BSI electronic information services are also available which give details on all its products and services.