MITSUBISHI E700 INVERTER MANUAL EBOOK

Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.

Author: Duzilkree Mohn
Country: Austria
Language: English (Spanish)
Genre: Marketing
Published (Last): 1 April 2012
Pages: 222
PDF File Size: 9.57 Mb
ePub File Size: 2.88 Mb
ISBN: 475-9-55727-400-2
Downloads: 61047
Price: Free* [*Free Regsitration Required]
Uploader: Shaktijind

Page Selection of operation mode and operation location Parameter Selects the command source of the PU operation mode Pr.

Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller

The maximum output voltage is 10V DC. Page AM are proportional. The above parameters can be set when Pr. Page 93 Turn the digital dial clockwise to change it to the setting value of “10”.

Page Page – Stop selection Pr.

Page Selection of operation mode and operation location Parameter External operation mode Pr. Page Operation selection at power failure Parameter If offline auto tuning ended in error see the table belowmotor constants are not set. Mitsubishi e700 inverter manual Description Parameters referred to Adjust the output torque current of the motor Parameter Setting of stall prevention operation in high frequency range Pr.

Table of Contents Add to mitsubishi e700 inverter manual manuals Add. When the magnetic contactor is turned on while the inverter is operating, overcurrent protection of the inverter and such will activate.

Page Frequency setting by external terminals Parameter Remote setting function When using the remote setting function, following frequencies can be compensated to the fre- quency set by RH and RM operation according to the operation mode. Page The mitsubishi e700 inverter manual mode cannot be switched directly mitsubizhi the PU operation mode and network operation mode.

Page If protective functions of E.

Page 2 After setting “2” in Pr. PU signal output, assign the function by setting “10 source logic or sink logic ” in any of Pr. For removal and reinstallation of the cooling fans, refer mitsubishi e700 inverter manual section mitsubishi e700 inverter manual. The po- tentiometer is supplied with a voltage of 5V through terminal 10 of the frequency inverter.

Page Shaft is locked. One to two years of periodic inspection cycle is recommended. However, it differs according to the installation environment.

Write disable error ER2: Page Stall prevention operation during acceleration may increase the acceleration time. Do not connect a mechanical mitwubishi. Special operation Parameter 6. Mitsubishi e700 inverter manual between output frequency and output voltage Setting range Pr. Simple mode parameter list Basic settings Operation Display Screen at powering on The monitor display appears.

In this case, use an approximate-effective value type.

If the PU connector is used to make a connection, use a distributor since a terminating resistor cannot be fitted. A screw that has been tighten mitsubishi e700 inverter manual tightly can cause a short circuit or malfunction due to the unit breakage. Description 2 Displays at powering off. When using the SU signal, set “1 positive logic or negative logic ” in Pr. When parameter setting is changed after creating the initial value change list, the setting will be reflected to the initial value change list next time.

When the start signal is turned off, the inverter decelerates the motor to a stop mitsubishi e700 inverter manual the preset deceleration time, but when the MRS signal is turned on, the motor coasts to a stop.

MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.

PUE and a motor stops as set in Pr. OV3 OV During Dec Indication FR-PU07 Name Regenerative over voltage shut-off during deceleration or stop If regenerative energy causes the inverter’s internal main circuit DC voltage to reach or Description exceed the specified value, the protective circuit is activated to stop mitsugishi inverter output. In this case, the terminal inputs are ORed. For detailed informa- tion refer to section 6.

Note that inberter output voltage of the inverter cannot exceed the power supply voltage. Mitsubiehi list with mitsubishi e700 inverter manual codes 3 Can be written by only communication from the PU connector. Motor brake and stop operation Parameter When a mitsubishi e700 inverter manual power factor converter FR-HC is used and automatic restart after instan- taneous power failure function is made valid.

Corrective action 1 Turn off the RES signal. Frequency setting e70 analog input terminal 2, 4 Parameter Perform operation by analog mitsubishi e700 inverter manual current When the pressure or temperature is controlled constant by a fan, pump, etc.

You can find a detailed description of the operation panel with examples in section 4. Reverse rotation start Tab. Rs Communication PU connector Mitsubishi e700 inverter manual 3. Brake Sequence Function pr. Phase, v Class Specifications Appendix A.

Mitsubishi Electric FR-E700 Instruction Manual

This operation is performed in PU mode. The half-tone screened areas indicate the main speed setting. Page Function assignment of external terminals Parameter When you refer to Fig. Page 46 Main circuit connection Wiring Total wiring length The maximum possible length of the motor cables depends on the capacity of mitsubishi e700 inverter manual inverter and the selected carrier frequency. Refer to the in- struction manual of the FR Mnaual for details.

Author: admin